Quick Tips — Unbutton Snags from the Backside

by | Sep 25, 2018 | 7 comments

Get your nymphs down to the fish. Put them in the strike zone — low — where the trout live. Keep your streamer near the riverbed because that’s where the baitfish are. Cast your flies over by that wet log. Trout love structure.

It’s all true. And to fish well, to be effective with our underwater patterns, we must take chances. Get low, but not so low that you hang up every cast. Target the structure and get close, but not so close that you drive the hook into a dead log.

Snags happen.

I’ve fished with guys that see every hang up as a failure — every lost fly as a mistake. But inevitably, that mindset breeds an overcautious angler, too careful and just hoping for some good luck.

Hang ups are not a failure. For a good angler, they are a calculated risk — an occasional consequence after assessing probability against skill, situation and loss. We all hang up the fly sometimes. So what.

Now let’s talk about how to pop loose that underwater snag.

Don’t Drive It Home

Let’s assume you cast upstream and the fly is drifting back down toward you when the line stops.

Good fishing is about being in contact with the flies. So the instant the fly stops (whether it touches a rock or a trout’s teeth) we should see it or feel it. Usually, we set the hook.

And that’s a good thing. Since we set when the line pauses, the fly doesn’t have much chance to bury itself underneath a complicated mass of rocks and tree parts. When the angler’s rig is in touch with the flies, most snags end up on the edge of something — like a rock.

When we set the hook on a rock, the worst thing to do is keep setting the hook into the rock. Don’t do that. Don’t pull downstream over and over and expect the fly to come out.

Instead, try a different angle. Try pulling up and then maybe sideways.  Half the time, that works. But when it doesn’t,a good pull on the snag 180 degrees from the angle it went in is almost a sure thing. Unless the hook is buried in wood, you’re getting your fly back. Here’s more . . .

Get On the Backside

Wade to an angle that gets your rod tip behind the fly — upstream from where it came. Often, it takes only a step or two. With a long fly rod we can reach behind the nymph and pull it out — reverse of the way it went in.

The backside angle need to be deliberate and precise. Pull 180 degrees from the angle the fly went in, and the fly will release will little effort. Most often, that pull is directly upstream, so it takes low rod angle and a very intentional placement of the rod tip upstream of the snag.

What’s the best way to get that angle?

Don’t Blow ‘Em Up

Wade directly behind the snag, stripping in slack as you go, until you can reach with the rod tip and get that low 180 degree angle on the upside of the snag. Then pull if free.  This approach ruins far fewer fishing opportunities than if you wade upstream and beside the snag to get the angle. Wading above or next to the snag is simply unnecessary, and it blows up all the fish in a wider area.

Snags happen. We deal with it and get back to fishing. But we don’t want to lose more opportunities for eager fish than we have to. Wading behind the snag and reaching in front simply saves more water — far more.

The Push-Button Release

So the next time you trout-set on a stick-fish, don’t drive the hook home with another hard pull. Change the angle and pull it from the backside –180 degrees. It’ll pop loose.

This trick is so reliable that my friend, Paul, calls it the push-button release. It’s just another tip that makes fishing more fun out there.

Fish hard, friends.

 

** Donate ** If you enjoy this article, please consider a donation. Your support is what keeps this Troutbitten project funded. Scroll below to find the Donate Button. And thank you.

 

Enjoy the day.
Domenick Swentosky
T R O U T B I T T E N
domenick@troutbitten.com

 

Share This Article . . .

Since 2014 and 900+ articles deep
Troutbitten is a free resource for all anglers.
Your support is greatly appreciated.

– Explore These Post Tags –

Domenick Swentosky

Central Pennsylvania

Hi. I’m a father of two young boys, a husband, author, fly fishing guide and a musician. I fish for wild brown trout in the cool limestone waters of Central Pennsylvania year round. This is my home, and I love it. Friends. Family. And the river.

More from this Category

DIY – Bar Boots

DIY – Bar Boots

I burn through boot soles fast. And cheap boots with poor foot support are a bad idea when you're wading heavy runs and putting full days on the water with lots of hiking, so I was spending about $150 every ten months on a new pair of boots. I used to resole my own...

A Better Streamer Box

A Better Streamer Box

After many years of carrying a select group of my favorite streamers in a fairly small box, I now find myself in an experimental phase with the big bugs again.  I'm generally in the camp that believes presentation is far more important than pattern, but trying new...

The Backing Barrel

The Backing Barrel

A decade ago I learned about euro-nymphing, and I was impressed with the rig. I gradually made the switch from a Joe Humphreys nymphing style, worked my way through the short line tactics, then lengthened the leader and learned to fish at distance.  I believe...

What do you think?

Be part of the Troutbitten community of ideas.
Be helpful. And be nice.

7 Comments

  1. I find throwing a roll cast or two on the back side of the snag will dislodge it most of the time

    Reply
    • Thanks Jon, that’s a good tip when you have enough fly line involved. But for most of us long liners, that’s one of the downsides — no roll casts.

      Reply
  2. I learned from Front Range legend Ed Engle, you gotta lose flies to catch fish. So I do more of both now. I’ll take that trade-off! A guy near you, Domenick, Matt Kowalchuk of the Feathered Hook, helped me get better with this fly-freeing technique you just wrote about. I’ve gotten better at it and it really helps you save your flies, and reduces the time when you’re not fishing.

    Reply
  3. Yes, spot on, that works for me, I get upstream and try gentle pulls first, then tension on the line and tap the rod, and circular movements with the rod tip as well, final try is to let the line go slack, then pull again with the rod tip down in the water to get another angle. On most of my waters, I can wade over and reach down and pluck the nymph out if all thats failed-making sure my feet are well planted and bending slowly to avoid joining the nymph on the snag LOL. I like to get stuff back in when I can as I don’t like leaving hooks and or nylon behind.

    Reply
  4. Nice post, another way is to do a roll cast that goes beyond where the fly is hooked then gently lift up at the end.

    Reply
  5. I have had some luck stripping some line off my Reel and sending a roll cast towards my fly.

    Reply

Submit a Comment

Your email address will not be published.

Recent Articles

Recent Posts

Domenick Swentosky

Central Pennsylvania

Hi. I’m a father of two young boys, a husband, author, fly fishing guide and a musician. I fish for wild brown trout in the cool limestone waters of Central Pennsylvania year round. This is my home, and I love it. Friends. Family. And the river.

Pin It on Pinterest